Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download

Page: 9 / 294

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

Front position lamp

12V - LED

Speedometer lamp

12V - LED

Hi beam indicator

12V - LED

Neutral lamp telltale

12V - LED

Turn signal telltale

12V - LED

Turn signal

12V, 10W * 4 Nos.

Horn

12V, 2.5 Amp.

Starter Motor

12V, 0.7 KW

Instrument Cluster

Digital cluster with main
and compass LCD

Side Stand indicator

LCD Indication

FF.

DIMENSIONS

Length

2190 mm

Width

840 mm

Height

1360 mm

Wheel base

1465 mm

Ground clearance.

220 mm

Saddle Height

800 mm

WEIGHTS

Kerb weight (90% fuel&oil)

191 kgs.

Max. Pay load

174 Kgs.

WARNING

Using bulbs/ electrical gadgets
other than specified rating
may lead to overloading/
eratic behaviour / premature
failure of electrical system.

Modifications or fitments
which are not approved by
Royal Enfield, will seriously
affect the performance of the
vehicle and will render the
warranty void.

Values / Dimensions
mentioned above are
for reference only.

In view of continuous
improvements being
done on our
motorcycles, the
specifications are
subject to change
without prior notice.

VEHICLE & VEHICLE SYSTEMS

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands