Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download Page 90

Page: 90 / 294

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle/

Instructions

11.8 Front Wheel

Support front end of
engine suitably such
that the front wheel is
off the ground.

Loosen pinch bolt on
right fork end with 6
mm Allen key.

Hold spindle on right
side and remove spindle
nut and washer from left
side.

Support wheel and pull
out spindle from right
side.

Remove wheel along
with wheel speed sensor
and spacer.

Remove speedo sensor.

Place a suitable spacer of
4 mm thickness,
between the brake pads
to avoid accidental
compression of the
brake lever.

CAUTION:

Do not press the brake lever
when wheel is removed as
this will result in the brake
pads coming out too far
from the brake caliper.

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands