Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download

Page: 212 / 294

211

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble /

Instructions

44.21

Fuel Injector

Hex U nut: M6 X 1

Ring spanner: 8mm

Locate fuel Injector on
the inlet side of the
cylinder head below the
fuel tank.

Locate the spacer in the
stud.

Locate hex nut from top
of injector cap assembly
and place injector cap
along with “O” ring.

Locate worm clip on the
inlet fuel hose and locate
fuel hose on cap injector
assembly.

Ensure Ignition switch
and stop switch are in
OFF position.

Connect the wiring
coupler from the fuel
injector.

Assemble Seat assembly
and fuel tank.

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands