Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download Page 35

Page: 35 / 294

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

4.24

Rear chain
assembly and chain
adjustment

Assemble ‘O’ Rings on
the chain link and
assemble the link plate.

Assemble chain link lock
on the chain link,
ensuring the closed end
of the lock is towards the
normal direction of
rotation of the chain.

Tighten adjuster nuts on
LH & RH side evenly till
the chain has a slack of
20 to 25 mm on its top
run.

Ensure the reference
lines on the LH & RH chain
adjusters are matching
at the same reference
lines in the swing arm on
LH & RH sides.

Tighten rear wheel axle
nut to torque.

Tighten lock nuts against
the adjuster nuts on LH
& RH sides.

Hex U Nut: M17

Socket Spanner: 24mm.

Torque: 70-80Nm
(7.0-8.0Kg.M)

4.25

Gear Shifter /
Linkage

Locate small lever on
gear shift shaft, ensuring,
small lever is vertical to
ground and the gear
shift pedal is parallel to
rider footrest LH.

Assemble Hex bolt on
gear shift lever short
from the front side and
tighten to torque.

Hex Flange Bolt : M6X20

Socket Spanner : 10mm.

Torque: 10Nm(1.0Kg.M)

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Brands by name

Popular brands

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Brands by name

Popular brands