Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download

Page: 20 / 294

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Dismantle/

Instructions

4.9

Steady Engine
Bracket

Hold U nut at the cylinder
head mounting area
with a double end
spanner and loosen Hex
bolt at the front of the
steady engine bracket.

Remove the bolt and
nut.

Support steady engine
bracket, Loosen &
remove the 2 Flanged
hex bolts at the rear end
of the bracket and
remove the bolts and
steady engine bracket.

Flanged hex bolt: M10

Socket Spanner: 12mm

Flanged hex nut: M10

Socket Spanner: 12mm

4.10

Throttle cable

Push rubber grommets
down and loosen hex
nuts completely.

Gently pull throttle cable
from bracket to release
the threaded position
from the bracket.

Remove inner cable
from the throttle body
rotor eyelet.

Double End Spanner:
13mm

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands