Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download

Page: 37 / 294

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

No.

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

4.28

Throttle body &
Fuel Injector

A. Throttle Body

Ensure worm clip is
located on air filter
bellow.

Locate throttle body
inside air filter bellow.

Ensure clip hose is
located on inlet manifold
adaptor.

Assemble inlet manifold
adaptor on throttle body.

Locate ‘O’ ring on Inlet
manifold.

Position inlet manifold
adaptor (with throttle
body) against inlet mani-
fold. Ensure the 2
mounting holes are
aligned.

Assemble new copper
washers on the 2 hex soc
head cap screws and
insert from the inlet
manifod adaptor end.

Assemble 2 hex nuts on
the screws and tighten
adaptor to manifold -
inlet.

Tighten worm clip screw
on air filter bellow and
inlet manifold adaptor.

Insert valve - Bi Starter
plunger into throttle
body are tighten the
plastic hex nut to throttle
body sufficiently.

Hex Soc. Hd. Cap Screw :
M6 x 25

Hex nylock nut : M6

Allen Key : 5 mm

Double end spanner :
10mm

Torque : 10Nm (1.0 Kg.M)

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands