Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download Page 161

Page: 161 / 294

160

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

Fastener, Size, Tool Usage, Precautions, Photos

Aggregate to Assemble/

Instructions

13.3

Front Disc Brake

Install brake pad on the
piston side first with its
friction material facing
outside.

Install the other brake
pad with the friction
material facing the
opposite brake pad.

No.

13.3

Brake pads in
caliper

Apply Silicon grease on
the pin OD and assemble
the Pin bolt by pressing
gently through the
brake pads into caliper
body.

NOTE:

Ensure pads are positioned
and locked correctly in the
mounting bracket lug.

Tighten the pins to the
caliper body.

Assemble Grub screws
on the pins and tighten.

Brake pad pins

Allen key: 5mm

Torque: 20Nm (2.0Kgm)

Grub screws

Screw driver

Torque: 3Nm (0.3Kgm)

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands

Royal Enfield HIMALAYAN EURO IV 2017, Service Manual

Search results

Summary of Contents for HIMALAYAN EURO IV 2017

Reviews:

Related manuals for HIMALAYAN EURO IV 2017

Brands by name

Popular brands