Royal Enfield HIMALAYAN EURO IV 2017 Service Manual Download | Manualshive

Page: 225 / 294

background image

224

ROYAL ENFIELD HIMALAYAN EURO IV VEHICLE SERVICE MANUAL

STEP 3 :

The positive probe of the multimeter shall be kept on all the 3 phase terminals one by one and the

condition of the 3 diodes to be checked as mentioned in Step 2.

STEP 4 :

To check the condition of other 3 negative diodes, positive probe (Red colour) of the multimeter shall be kept on the
negative terminal of DC output (black wire with eyelet/single pole connector) and negative probe (Black colour) of
the multimeter shall be kept on anyone of the 3 phase terminals (yellow wire).

If the diode is good, then the multimeter will show a voltage drop of 0.4~0.7V.

If diode has failed, multimeter will show either open or short with beep sound, then Replace the RR unit.

STEP 5 :

All the three diodes to be checked by keeping the multimeter negative probe on all the 3 phase terminals one by one.
If the RR Unit is not working, replace with good working RR Unit.

«
...
223
224
225
226
227
...
»

Summary of Contents for HIMALAYAN EURO IV 2017







































































































































































































































































































Reviews:

No comments

Related manuals for HIMALAYAN EURO IV 2017

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Öhlins Pages: 2

Brand: Qlink Pages: 44

Brand: Crivit Pages: 70

Brand: Gentex Pages: 15

Mambo Evo PURE CARBON

Brand: LAZER Pages: 13

Brand: Memphis Shades Pages: 2

Brand: Denali Pages: 2

Brand: Yamaha Pages: 112

Brand: hepco & becker Pages: 4

6304541 00 02 chrom

Brand: hepco & becker Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands