Rosemount 3051S Series Reference Manual Download Page 30

Page: 30 / 190

Reference Manual

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

1. Expand the

Gas

category.

2. Select the

Custom Gas

option.

3. Enter the

Nominal Operating Pressure

and

Temperature Ranges

. Engineering Assistant will use these

ranges to identify the pressure and temperature values at which the fluid properties are required.

4. Select

Next

to proceed to the

Custom Gas Fluid Properties

tab.

5. Enter the

Molecular Weight

of the Custom Gas. When the molecular weight of the gas is entered, the

other data entry fields on the tab are enabled as shown in

Figure 2-16 on page 22

6. Select either

Density

Compressibility

and enter data.

Note

All pressure and temperature values may be edited except the minimum and maximum values. The
minimum and maximum values were set on the

Fluid Selection

tab.

7. Enter the

Density

Compressibility

at reference conditions.

8. Enter the

Custom Gas Viscosity

at the given temperatures. Note that all temperature values may be

edited except the minimum and maximum temperatures.

9. Enter the

Custom Gas Isentropic Exponent

10.Select

Next

to continue with the flow configuration on the

Primary Element Selection

tab.

11.Proceed with the steps in

“Primary element selection” on page 13

Figure 2-16. Custom Gas Fluid Properties Tab

Summary of Contents for 3051S Series































































































































































































Search results

Summary of Contents for 3051S Series

Reviews:

Related manuals for 3051S Series

Brands by name

Popular brands

Rosemount 3051S Series, Reference Manual

Search results

Summary of Contents for 3051S Series

Reviews:

Related manuals for 3051S Series

Brands by name

Popular brands