manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 24

16

Reference Manual

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

Figure 2-11. Save/Send Configuration Tab (Offline Mode)

2. Select the icon above each window to be taken to the appropriate screen to edit the configuration 

information. To return to the 

Save/Send

 tab, select 

Save/Send

 in the left menu.

3. When all information is correct, see 

“Sending a configuration in offline mode” on page 16

 or 

“Sending 

a configuration in online mode” on page 17

. 

Note

The user will be notified if the configuration has been modified since it was last sent to the transmitter. A 
warning message will be shown to the right of the 

Send Flow Data

 and/or 

Send Device Data

 check boxes.

Sending a configuration in offline mode

1. To send the configuration, select the 

Send To

 button. 

Note

The 

Send Flow Data

 and/or 

Send Device Data 

check boxes can be used to select what configuration data is 

sent to the transmitter. If the check box is unselected, the corresponding data will not be sent.

2. The Engineering Assistant Device Connection screen will appear, see 

Figure 2-12 on page 17

.

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands