manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 41

33

Reference Manual 

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

2.6.5

Communication setup

The

 Comm Setup

 tab allows the settings for burst mode and multidrop communications to be 

configured. 

Figure 2-23. Device - Comm Setup Tab

Burst mode

When 

Burst Mode Enable

 is set to on, the Rosemount 3051SMV sends up to four HART variables to the 

control system without the control system polling for information from the transmitter.

When operating with 

Burst Mode Enable

 set to on, the transmitter will continue to output a 4–20 mA 

analog signal. Because the HART protocol features simultaneous digital and analog data transmission, 
the analog value can drive other equipment in the loop while the control system is receiving the digital 
information. Burst mode applies only to the transmission of dynamic data (process variables in 
engineering units, primary variable in percent of range, and/or analog output), and does not affect the 
way other transmitter data is accessed. 

Access to information that is not burst can be obtained through the normal poll/response method of 
HART communication. A Field Communicator, AMS Device Manager, Engineering Assistant, or the 
control system may request any of the information that is normally available while the transmitter is in 
burst mode. 

Enabling burst mode 

To enable burst mode, select 

On

 from the 

Burst Mode Enable 

drop-down menu under the 

Burst Mode

 

heading. 

Mass and energy flow Fast Keys

1, 4, 3, 3

Direct process variable output Fast Keys

1, 4, 3, 3

Mass and energy flow Fast Keys

1, 4, 3, 3, 3

Direct process variable output Fast Keys

1, 4, 3, 3, 3

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands