Rosemount 3051S Series Reference Manual Download Page 9

Page: 9 / 190

Reference Manual

00809-0100-4803, Rev GA

Introduction

September 2017

Introduction

Section 1

Introduction

1.1

Using this manual

The sections in this manual provide information on installing, operating, and maintaining the
Rosemount

™

3051S MultiVariable

™

Transmitter (Rosemount 3051SMV). The sections are organized as

follows:



Section 2: Configuration

provides instruction on commissioning and operating Rosemount 3051SMV.

Information on software functions, configuration parameters, and online variables is also included.



Section 3: Installation

contains mechanical and electrical installation instructions.



Section 4: Operation and Maintenance

contains operation and maintenance techniques.



Section 5: Troubleshooting

provides troubleshooting techniques for the most common operating

problems.



Section 6: Safety Instrumented Systems Requirements

contains identification, commissioning,

maintenance, and operations information for the Rosemount 3051S MultiVariable Safety
Instrumented System (SIS) Safety Transmitter.



Appendix A: Specifications and Reference Data

supplies reference and specification data, as well as

ordering information.



Appendix B: Product Certifications

contains intrinsic safety approval information, European ATEX

directive information, and approval drawings.

Models covered

The following Rosemount 3051SMV Transmitters are covered in this manual:

Table 1-1. Rosemount 3051SMV Measurement with Fully Compensated Mass and Energy Flow

Output

Measurement type

Multivariable type - M

Differential pressure, static pressure, temperature

Differential pressure and static pressure

Differential pressure and temperature

Differential pressure

Table 1-2. Rosemount 3051SMV Measurement with Direct Process Variable Output

Measurement type

Multivariable type - P

Differential pressure, static pressure, temperature

Differential pressure and static pressure

Differential pressure and temperature

Coplanar static pressure and temperature

In-line static pressure and temperature

Summary of Contents for 3051S Series































































































































































































Search results

Summary of Contents for 3051S Series

Reviews:

Brands by name

Popular brands

Rosemount 3051S Series, Reference Manual

Search results

Summary of Contents for 3051S Series

Reviews:

Brands by name

Popular brands