manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 108

100

Reference Manual

00809-0100-4803, Rev GA

Operation and Maintenance

September 2017

Operation and Maintenance

4.6.2

Housing assembly including feature board electronics

Field device labels 

The SuperModule label reflects the replacement model code for reordering a complete transmitter, 
including both the SuperModule assembly and Plantweb

™

 housing. The Rosemount 3051SMV model 

code stamped on the Plantweb housing nameplate can be used to reorder the Plantweb housing 
assembly. 

Upgrading feature board electronics

The Rosemount 3051SMV allows feature board electronics upgrades. Different feature board electronics 
assemblies provide new functionality and are easily interchanged for upgrade. When replacing or 
upgrading the feature board electronics, use the 

“Rosemount 300SMV housing kit” on page 144

 which 

also includes the appropriate Plantweb housing. 

Upgrading or replacing the housing assembly including feature board 
electronics 

Remove the feature board 

The Rosemount 3051SMV feature board is located opposite the field terminal side in the Plantweb 
housing. To remove the feature board, perform the following procedure:

1. Remove the housing cover opposite the field terminal side.

2. Remove the LCD display, if applicable. To do this, hold in the two clips and pull outward. This will 

provide better access to the two screws located on the feature board.

3. Loosen the two captive screws located on the feature board.

4. Pull out the feature board to expose and locate the SuperModule connector, see 

Figure 4-10 on 

page 101

.

5. Press the locking tabs and pull the SuperModule connector upwards (avoid pulling wires). Housing 

rotation may be required to access locking tabs. See 

“Housing rotation” on page 68

 for more 

information.

Figure 4-9. SuperModule Connector View

A. Feature board
B. SuperModule connector

A

B

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands