manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 29

21

Reference Manual 

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

Note

The 

Fluid Properties

 tab is an optional step and is not required to complete a flow configuration. 

The Fluid Properties tab for the database gas air is shown in 

Figure 2-15

. The user may view the 

properties of the chosen fluid. The fluid properties are initially shown at nominal conditions. To view 
density, compressibility, and viscosity of the selected fluid at other pressure and temperature values, 
enter a 

Pressure

 and 

Temperature

 and select 

Calculate

.

Changing the pressure and temperature values on the 

Fluid Properties 

tab does not affect the flow 

configuration.

Figure 2-15. Fluid Properties Tab

6. Select 

Next

 to continue with the flow configuration on the 

Primary Element Selection

 tab.

7. Proceed with the steps in 

“Primary element selection” on page 13

.

Custom gas

The custom gas option should be used for fluids not in the database such as proprietary fluids or gas 
mixtures. To properly calculate the fluid properties, the compressibility factor or density needs to be 
entered at specific pressure and temperature values based on the operating ranges entered by the user. 
The pressure and temperature values may be edited as needed. The editable values are shown in fields 
with white backgrounds. For best performance, it is recommended that, whenever possible, the com-
pressibility or density values be entered at the suggested pressure and temperature values.
To ease entering the compressibility/density or viscosity values, data can be copied from a spreadsheet 
and pasted into the grid. The recommended process is to copy the pressure and temperature values 
from the table on the Engineering Assistant screen to assist in computing the density or compressibility 
values. Once the compressibility or density values are computed, they may then be copied from the 
spreadsheet and pasted into the grid on the 

Custom Gas Fluid Properties

 tab.

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands