manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 113

105

Reference Manual 

00809-0100-4803, Rev GA

Operation and Maintenance

September 2017

Operation and Maintenance

Note

Due to the sensitivity of the Range 1 DP Sensor, extra steps are required to optimize performance. It is 
necessary to temperature soak the assembly using the following procedure. 
1. After replacing O-rings on DP Range 1 transmitters and re-installing the process flange, expose the 

transmitter to a temperature of 185 °F (85 °C) for two hours. 

2. Re-tighten the flange bolts in a cross pattern.
3. Again, expose the transmitter to a temperature of 185 °F (85 °C) for two hours before calibration.

4.6.6

SuperModule assembly

To reorder an upgrade or replacement SuperModule assembly, use the Rosemount 3051SMV 

“Ordering 

information” on page 138

 but replace the housing option code with ‘00’.

1. Remove the housing assembly per 

“Upgrading or replacing the housing assembly including feature 

board electronics” on page 100

.

2. Remove currently installed SuperModule assembly from process flange per 

“Flange and drain vent” 

on page 103

.

3. Reassemble replacement or upgraded SuperModule assembly to process flange per 

“Flange and drain 

vent” on page 103

.

4. Reassemble the housing assembly per 

“Upgrading or replacing the housing assembly including 

feature board electronics” on page 100

.

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands