Rosemount 3051S Series Reference Manual Download Page 8 | Manualshive

Page: 8 / 190

background image

vi

Reference Manual

00809-0100-4803, Rev GA

Title Page

September 2017

Title Page

Failure to follow these installation guidelines could result in death or serious injury.



Make sure only qualified personnel perform the installation.

Explosions could result in death or serious injury.



Do not remove the transmitter cover in explosive atmospheres when the circuit is live.



Before connecting a Field Communicator in an explosive atmosphere, make sure the instruments in
the loop are installed in accordance with intrinsically safe or non-incendive field wiring practices.



Both transmitter covers must be fully engaged to meet flameproof/explosion-proof requirements.



Verify the operating atmosphere of the transmitter is consistent with the appropriate hazardous
locations certifications.

Electrical shock could cause death or serious injury.



If the sensor is installed in a high-voltage environment and a fault or installation error occurs, high
voltage may be present on the transmitter leads and terminals.



Use extreme caution when making contact with the leads and terminals.

Process leaks could result in death or serious injury.



Install and tighten all four flange bolts before applying pressure.



Do not attempt to loosen or remove flange bolts while the transmitter is in service.



Replacement equipment or spare parts not approved by Emerson for use as spare parts could reduce
the pressure retaining capabilities of the transmitter and may render the instrument dangerous.



Use only bolts supplied or sold by Emerson as spare parts.

Improper assembly of manifolds to traditional flange can damage the device.



For safe assembly of manifold to traditional flange, bolts must break back plane of flange web
(i.e., bolt hole) but must not contact the sensor module.

Improper installation or repair of the SuperModule

™

assembly with high pressure option (P0)

could result in death or serious injury.



For safe assembly, the high pressure SuperModule assembly must be installed with ASTM A193 Class 2
Grade B8M bolts and either a Rosemount 305 Manifold or a DIN-compliant traditional flange.

Static electricity can damage sensitive components.



Observe safe handling precautions for static-sensitive components.

The products described in this document are NOT designed for nuclear-qualified applications. Using
non-nuclear qualified products in applications that require nuclear-qualified hardware or products may
cause inaccurate readings.

For information on Rosemount nuclear-qualified products, contact your local Emerson Sales
Representative.

«
...
6
7
8
9
10
...
»

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Related manuals for 3051S Series

Brand: LATNEX Pages: 55

Brand: Laser Technology Pages: 11

Brand: Laser Technology Pages: 62

Brand: Magnescale Pages: 64

SourceMeter 2430

Brand: Keithley Pages: 141

Brand: Yamaha Pages: 12

Brand: H-Star Pages: 36

Brand: KALATEL Pages: 38

Brand: Fluke Pages: 6

Brand: Sensitech Pages: 2

Brand: Novus Pages: 52

Brand: Rockler Pages: 4

Brand: E+E Elektronik Pages: 48

Brand: Agilent Technologies Pages: 26

Brand: DynAmp Pages: 43

Mini-SuperGraph II

Brand: NOMIS Seismographs Pages: 44

Brand: K&K Sound Pages: 2

Brand: Ziton Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands