manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 58

50

Reference Manual

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

Follow these steps to configure a custom unit:

a.

Custom Unit

: Enter the desired custom unit label to be displayed for the 

Totalized Reading

. Up to 

five characters including letters, numbers, and symbols can be entered in the custom unit field.

Note

It is recommended that the Custom Unit be entered in upper case letters. If lower case letters are 
entered, the LCD display will show upper case letters. Additionally, the following special characters are 
recognized by the LCD display: hyphens (“-”), percent symbols (“%”), asterisks (“*”), forward slashes (“/”) 
and spaces. Any other character entered for the Custom Unit will be displayed as an asterisk (“*”) on the 
LCD display. The following warning will be returned indicating these changes: “Custom Unit contains 
characters that will display in upper case or asterisks on LCD display. The DCS will display as entered.” 

b.

Base Unit

: From the drop-down menu, select a base unit to be used for the custom unit 

relationship.

c.

Base per Custom

: Enter a numeric value that represents the number of base units per one 

custom unit. The Rosemount 3051SMV uses the following convention:

Base per Custom = 

Example

Custom Unit: kg
Base Unit: g

Because:

1 kg (Kilogram) = 1000 g (Grams)

Base per Custom = 

 = 

 = 1000

The values of Base per Custom for common totalizer units are shown in 

Table 2-11

.

d. Select 

Apply

.

e.

Totalizer Unit

: From the drop-down menu, select the custom unit that was created in 

Step b

.

Note

The custom unit may not be available as a selection in the 

Totalizer Unit

 drop-down menu until the 

drop-down menu is refreshed. To refresh the drop-down menu, navigate to the 

Basic Setup

 tab and then 

return to the 

Variables - Totalizer

 tab.

Table 2-11.  Common Custom Units - Totalizer

Custom unit

Base unit

Base per custom

Millions of Normal Cubic Meters (MMNCM)

NmlCum

1000000

Millions of Standard Cubic Feet (MMSCF)

StdCuft

1000000

Millions of Standard Cubic Meters (MMSCM)

StdCum

1000000

Thousands of Metric Tons (KMTON)

MetTon

1000

Thousands of Normal Cubic Meters (KNCM)

NmlCum

1000

Thousands of Short Tons (KSTON)

STon

1000

Thousands of Standard Cubic Feet (KSCF)

StdCuft

1000

Thousands of Standard Cubic Meters (KSCM)

StdCum

1000

Number of Base Units

1

x

Custom

x

Unit

----------------------------------------------------------------------

Number of Base Units

1

x

Custom

x

Unit

----------------------------------------------------------------------

1000 g

⋅

1 kg

⋅

---------------------

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands