manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 127

Reference Manual 

00809-0100-4803, Rev GA

Safety Instrumented Systems Requirements

September 2017

119

Safety Instrumented Systems Requirements

Section  6

Safety Instrumented Systems 
Requirements

Safety Instrumented Systems (SIS) Certification   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 119
Rosemount 3051SMV safety certified identification  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 119
Installation in SIS applications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 119
Configuring in SIS applications   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 120
Rosemount 3051SMV SIS operation and maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 121
Inspection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 122

6.1

Safety Instrumented Systems (SIS) Certification

The safety-critical output of the Rosemount 3051SMV is provided through a two-wire, 4–20 mA signal 
representing pressure. The Rosemount 3051SMV safety certified pressure transmitter is certified to: Low 
Demand; Type B.
SIL 2 for random integrity @ HFT=0
SIL 3 for random integrity @ HFT=1
SIL 3 for systematic integrity

The Rosemount 3051SMV must be installed per manufacturer’s instructions, specifications and the 
materials must be compatible with process conditions.

The HART

®

 Protocol is only used for setup, calibration, and diagnostic purposes and is not for safety 

critical operation.

6.2

Rosemount 3051SMV safety certified identification

All Rosemount 3051SMV Transmitters must be identified as safety certified before installing into SIS 
systems. 

To identify a safety certified Rosemount 3051SMV:

1. Verify the model string contains Rosemount 3051SMV and QT.

–

If the transmitter was ordered as part of a flowmeter, verify the model string reads Rosemount 
3051SFx(1–7) and QT.

2. Verify software revision is 3.

6.3

Installation in SIS applications

Installations are to be performed by qualified personnel. No special installation is required in addition to 
the standard installation practices outlined in this document. Always ensure a proper seal by installing 
the electronics housing cover(s) so that metal contacts metal. 

Environmental and operational limits are available in 

Appendix A: Specifications and Reference Data

The loop should be designed so the terminal voltage does not drop below 12.0 Vdc when the 
transmitter output is set to 23 mA.

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands