manualshive.com logo in svg

Rosemount 3051S Series, Reference Manual

Share
Download
Rosemount 3051S Series Reference Manual Download Page 130

122

Reference Manual

00809-0100-4803, Rev GA

Safety Instrumented Systems Requirements

September 2017

Safety Instrumented Systems Requirements

5. Perform a two-point verification

(1)

 of the transmitter pressure over the full working range (and 

process temperature where applicable).

6. Remove the bypass and otherwise restore the normal operation.

7. Place the Security switch in the (

) position.

Note

The user determines the proof test requirements for impulse piping.

Automatic diagnostics are defined for the corrected % DU: The tests performed internally by the 

device during runtime without requiring enabling or programming by the user.

6.6

Inspection

6.6.1

Visual inspection

Not required

6.6.2

Special tools

Not required

6.6.3

Product repair

The Rosemount 3051SMV is repairable with limited replacement options. 

All failures detected by the transmitter diagnostics or by the proof-test must be reported. Feedback can 
be submitted electronically at 

Emerson.com/Rosemount/Report-A-Failure

 

All product repair and part replacement should be performed by qualified personnel.

6.6.4

Rosemount 3051SMV SIS reference

The Rosemount 3051SMV must be operated in accordance to the functional and performance 
specifications provided in 

“Specifications and Reference Data” on page 125

.

6.6.5

Failure rate data

The FMEDA report includes failure rates and the assumptions for how these failure rates were derived.

The report is available under 

Certificates and Approvals

 at

Emerson.com/Automation-Solutions/Pressure/Rosemount-3051SMV

6.6.6

Failure values

Safety Deviation (defines what is dangerous in a FMEDA): ±2.0% of analog output span
Transmitter response time: provided in 

“Dynamic performance ambient temperature effect” on 

page 127

.

Self-diagnostics Test Interval: At least once every 60 minutes

1. 

If the two-point process temperature verification is performed with electrical instrumentation, this proof test will not detect any failures of the sensor.

Summary of Contents for 3051S Series































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands