Ricoh TH-C1 Technical Bulletin Download Page 116

Page: 116 / 203

echnical

ulletin

PAGE: 1/1

Model:

Model TH-C1

Date:

26-Apr-06

No.:

RB156028

Subject: SC874/SC875

Prepared by:

H.K.

From:

1st Tech. Support Sec. Service Support Dept.

Classification:

Troubleshooting
Mechanical
Paper path

Part information
Electrical
Transmit/receive

Action required
Service manual revision
Retrofit information

Other ( )

The Service Manual was changed as shown below.

Add

the following new SC descriptions to your Service Manual:

Code No.

Symptom

Action

Delete All error 1: HDD

874 D

An HDD/NVRAM data error is
detected after the “Delete All
Memory” feature of the Data
Overwrite Security Unit is
executed.

Note:

The source of the error is

a Data Overwrite Security Unit
that is run from an SD card.

Turn the main switch OFF/ON and try

the operation again.

Install the Data Overwrite Security

Unit again. For more, see RTB
RGene021.

Replace

the

HDD.

Delete All error 2: Data area

875 D

An error occurs while the

Data

Overwrite Security Unit is
deleting data from the hard
drive.

Note:

The source of the error is

a Data Overwrite Security Unit
that is run from an SD card.

Turn the main switch OFF/ON and try

the operation again.

Summary of Contents for TH-C1












































































































































































































Search results

Summary of Contents for TH-C1

Reviews:

Related manuals for TH-C1

Brands by name

Popular brands

Ricoh TH-C1, Technical Bulletin

Search results

Summary of Contents for TH-C1

Reviews:

Related manuals for TH-C1

Brands by name

Popular brands