Ricoh TH-C1 Technical Bulletin Download Page 145

Page: 145 / 203

echnical

ulletin

PAGE: 1/

Model: Model TH-C1

Date:

11-Jul-06

No.:

RB156033

Subject:

Fusing Unit & PCU

Prepared

by:

H.K.

From:

1st Tech. Support Sec. Service Support Dept.

Classification:

Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Product Safety

Other (

)

SYMPTOM

The PCU cannot be pulled out if the fusing unit is not pulled out first.

Note:

This does not affect image quality in any way.

CAUSE

The front side plate (B1544118) of the fusing unit overlaps with the PCU as shown.

Note:

Previously, the front side plate was separated into two parts to meet a field

request (Front Side Plate: B1544118, Front Adjustment Side Plate: B1544117).
The height can be adjusted to fix image skew.

Summary of Contents for TH-C1












































































































































































































Search results

Summary of Contents for TH-C1

Reviews:

Related manuals for TH-C1

Brands by name

Popular brands

Ricoh TH-C1, Technical Bulletin

Search results

Summary of Contents for TH-C1

Reviews:

Related manuals for TH-C1

Brands by name

Popular brands