Ricoh BBP-PRSP213NW1 Manual Download Page 226 | Manualshive

Page: 226 / 268

background image

MF

Error and Status Messages on the Screen

Messages are listed in alphabetical order in the table below.
"X" indicates the parts of the messages that appear differently depending on a specific situation, such as
the paper sizes, paper types, or tray names.

Message

Causes

Solutions

2XXX14

The machine was not able to
print the received fax, or the
machine's memory reached
capacity while receiving a fax
because the document was too
large.

• The paper tray was empty. Load

paper in the paper tray. See page 45
"Loading Paper".

• The paper tray did not contain A4,

Letter, or Legal size paper. Load valid
size paper in the tray, and configure
the paper size settings under [System
Settings] accordingly.

• A cover or tray was open. Close the

cover or tray.

• There was a paper jam. Remove the

jammed paper. See page 210
"Paper Feed Problems".

• A print cartridge was empty. Replace

the print cartridge. See page 203
"Replacing the Print Cartridge".

• The received fax was too large. Ask

the sender to resend the document in
parts as several smaller individual
faxes, or to send at a lower
resolution.

ADF Orig. Misfeed
Open ADF Cover
and remove paper.

An original has been jammed
inside the ADF.

• Remove jammed originals, and then

place them again. See page 210
"Paper Feed Problems".

• Check the originals are suitable for

scanning. See page 54 "Placing
Originals".

Available: IDCard
Copy A4/A5/
A6/8.5x11/5.5x8.
5

ID card copy could not be
performed because the tray
does not contain the valid size

Specify the A4, A5, A6, 8.5 × 11 or
5.5x8.5 or Letter size paper for the tray
selected for printing copies. See page 145
"System Settings".

10. Troubleshooting

226

opal-p2_mf2_com_user_guide_00142156_eng.xml

Draft 2014/01/07

«
...
224
225
226
227
228
...
»

Summary of Contents for BBP-PRSP213NW1













































































































































































































































































Reviews:

No comments

Related manuals for BBP-PRSP213NW1

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 4

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 16

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 170

Brand: Samsung Pages: 165

Brand: Xerox Pages: 114

Brand: Oki Pages: 268

Brand: Oki Pages: 54

Brand: Oki Pages: 54

Brand: Oki Pages: 202

Brand: Oki Pages: 201

Brand: Oki Pages: 103

Brand: Oki Pages: 256

Brand: Oki Pages: 2

Brand: Oki Pages: 36

Brand: Oki Pages: 63

Brand: Oki Pages: 28

Brand: Oki Pages: 616

Brand: Oki Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands