Ricoh BBP-PRSP213NW1 Manual Download Page 228

Page: 228 / 268

Message

Causes

Solutions

Dest. is not
Programmed

No Quick Dial entry is
associated with the One Touch
button you pressed.

• Press a different One Touch button.
• Assign a registered destination to the

One Touch button. See page 80
"Registering Scan Destinations".

Dial Failed

The fax could not be sent.

• Confirm that the fax number you

dialed is correct.

• Confirm that the destination is a fax

machine.

• Confirm that the line is not busy.
• You may need to insert a pause

between dial digits. Press the [Pause/
Redial] key after, for example, the
area code.

Exceeded Max.E-
mail Size

The scan file exceeds the size
limit for files that can be sent
through e-mail.

• Configure [Resolution] under scan

settings to reduce the scanning
resolution. See page 135 "Scanner
Features Settings".

• Configure [Max. E-mail Size] under

scan settings to increase the allowed
size. See page 135 "Scanner
Features Settings".

Fax Job Memory
Overflow

The number of fax jobs in
memory (unsent or unprinted
faxes) has reached maximum,
so new jobs cannot be stored.

Wait until pending jobs have been
transmitted or printed.

Indep.Sply.Prt.Cart.

A non-supported print cartridge
is installed.

Remove and replace it with a print
cartridge specified by an authorized
dealer.

Internal Misfeed

Paper has been jammed in the
machine.

Remove the jammed paper. See page 210
"Paper Feed Problems".

Memory Almost Full

Memory has almost reached
capacity during sort copy.

If several originals are still to be scanned,
it is recommended to start printing now,
and copy the remaining originals
separately. If originals are being scanned

10. Troubleshooting

228

opal-p2_mf2_com_user_guide_00142156_eng.xml

Draft 2014/01/07

Summary of Contents for BBP-PRSP213NW1













































































































































































































































































Search results

Summary of Contents for BBP-PRSP213NW1

Reviews:

Related manuals for BBP-PRSP213NW1

Brands by name

Popular brands

Ricoh BBP-PRSP213NW1, Manual

Search results

Summary of Contents for BBP-PRSP213NW1

Reviews:

Related manuals for BBP-PRSP213NW1

Brands by name

Popular brands