Ricoh BBP-PRSP213NW1 Manual Download Page 230

Page: 230 / 268

Message

Causes

Solutions

Network is not Ready A scanned file could not be sent

because the machine has not
received IP address information
from the DHCP server
completely.

Wait until the machine receives the IP
address information completely, and then
try the operation again.

On Hook or Stop key The machine has been off-hook

for an extended period of time.

Put down the handset or press the [Clear/
Stop] key.

Out of Paper: X

The indicated tray has run out of
paper.

Load paper to the indicated tray. See
page 45 "Loading Paper".

Please Restart
Machine

The machine needs to be
restarted.

Turn off the power, and then turn it back
on.

Print Cart. Set Error

The print cartridge has not been
installed or has not been
installed correctly.

Reinstall the print cartridge. See page 203
"Replacing the Print Cartridge".

Remove Paper:
Bypass Tray

The machine failed to proceed
with the print job, because tray
1 was specified as the input tray
but paper was set in the bypass
tray.

Remove paper from the bypass tray.

Replace Required
Soon:
Print Cartridge

The print cartridge is almost
empty.

Prepare a new print cartridge.

Replacement
Required:
Print Cartridge

The machine has run out of
toner.

Replace the print cartridge. See page 203
"Replacing the Print Cartridge".

RX Comm. Error

A reception error occurred, and
the fax could not be received
correctly.

If possible, contact the sender of the fax
and ask them to resend it.

Scan (NW)
Disconnected

A scanned file could not be sent
because the Ethernet cable was
not connected properly.

Reconnect the Ethernet cable properly,
and then try the operation again.

10. Troubleshooting

230

opal-p2_mf2_com_user_guide_00142156_eng.xml

Draft 2014/01/07

Summary of Contents for BBP-PRSP213NW1













































































































































































































































































Search results

Summary of Contents for BBP-PRSP213NW1

Reviews:

Related manuals for BBP-PRSP213NW1

Brands by name

Popular brands

Ricoh BBP-PRSP213NW1, Manual

Search results

Summary of Contents for BBP-PRSP213NW1

Reviews:

Related manuals for BBP-PRSP213NW1

Brands by name

Popular brands