Ricoh BBP-PRSP213NW1 Manual Download Page 227

Page: 227 / 268

Message

Causes

Solutions

paper, which are A4, A5, A6,
8.5 × 11 or 5.5 × 8.5 size.

Busy

Fax transmission could not be
completed because the
destination's line was busy.

Wait for a while and send the fax again.

Cannot Copy This
Setting
Comb.: 2 on 1 / 4
on 1

Combined copying could not be
performed because the tray
does not contain the valid size
paper, which are A4, Letter, or
Legal size.

Specify the A4, Letter, or Legal size paper
for the tray selected for printing copies.
See page 145 "System Settings".

Cannot copy.
Set original to ADF.

Combined copying could not be
performed because the originals
were not placed in the ADF.

• Use the ADF, even when copying a

single sheet.

• If you need to use the exposure glass,

turn off combined copying in
[Duplex/Combine] under copy
settings, and then try again. See
page 132 "Copier Features Settings".

Check Paper Size

The paper size set for the
document differs from the size of
the paper in the indicated tray.

Press [FormFeed] to begin printing, or
press [JobReset] to cancel the job.

Check Paper Type

The paper type set for the
document differs from the type
of the paper in the indicated
tray.

Press [FormFeed] to begin printing, or
press [JobReset] to cancel the job.

Connection Failed

The line could not be connected
correctly.

• Confirm that the telephone line is

properly connected to the machine.

• Disconnect the telephone line from

the machine, and connect a standard
telephone in its place. Confirm that
you can make calls using the
telephone. If you cannot make calls
this way, contact your telephone
company.

Cooling down...

The engine has overheated.

Wait until the message disappears.

Cover open

A cover is open.

Close the cover completely.

Error and Status Messages on the Screen

opal-p2_mf2_com_user_guide_00142156_eng.xml

227

Draft 2014/01/07

Summary of Contents for BBP-PRSP213NW1













































































































































































































































































Search results

Summary of Contents for BBP-PRSP213NW1

Reviews:

Related manuals for BBP-PRSP213NW1

Brands by name

Popular brands

Ricoh BBP-PRSP213NW1, Manual

Search results

Summary of Contents for BBP-PRSP213NW1

Reviews:

Related manuals for BBP-PRSP213NW1

Brands by name

Popular brands