manualshive.com logo in svg

Rice Lake 181881, Technical Manual

Share
Download
Rice Lake 181881 Technical Manual Download Page 65

Appendix

© Rice Lake Weighing Systems

 

●

 All Rights Reserved

59

Figure 7-13. Install RF Module

13. Reinstall rear cover and handles with four bolts removed in 

Step 4 on page 55

.

7.4.3 Update Firmware

In order for wheel weigh pads and Ai-1 indicators originally supplied with Bluetooth® modules to use RF modules, their 

firmware must be updated.

  IMPORTANT: Firmware update supports Windows 10 and 11 computers.

NOTE: Firmware update duration varies; plan for approximately five to ten minutes for a wheel weigh pad and 25 to 45 

minutes for an Ai-1 Indicator.

1. Download 2.4 GHz Load Ranger firmware from: 

h

t

tps://www.ricelake.com/firmware

2. Unzip firmware file (files for Ai-1 and indicator wheel weigh pad are included):

NOTE: The Ai-1 indicator’s firmware file name starts with EGT while the wheel weigh pad’s firmware file name starts with 

Dfw.

RF Module

Communication Cable 

Antenna Wire

COM3

Summary of Contents for 181881











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands