manualshive.com logo in svg

Rice Lake 181881, Technical Manual

Share
Download
Rice Lake 181881 Technical Manual Download Page 63

Appendix

© Rice Lake Weighing Systems

 

●

 All Rights Reserved

57

7.4.2 Ai-1 Indicator hardware Retrofit

  WARNING: Disconnect charging cable before opening the enclosure. 

  WARNING: After enclosure is open, disconnect battery and power cable from CPU board. 

CAUTION: A grounding wrist strap must be worn to protect components from electrostatic discharge (ESD) when working 

inside the indicator.

Parts List

Figure 7-9. Ai-1 Indicator RF Retrofit Kit Parts (212111)

Indicator Ai-1 Retrofit Kit Installation

1. Turn off device and disconnect power cable.
2. Position Ai-1 indicator with bottom facing up.
3. Remove four cover mounting bolts, then remove cover.

  NOTE: Be aware, removing the retaining bolts also detaches handles.

Figure 7-10. Indicator Cover Retaining Bolts

Item No.

Description

Qty

1

2.4GHz Radio Frequency (RF) Module

1

2

Antenna

1

3

Phillips screw, 2.9 x 9.5 self-tapping screw

1

Table 7-7.  Ai-1 Indicator RF Retrofit Kit Parts

3

1

2

Retaining Bolts

Summary of Contents for 181881











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands