manualshive.com logo in svg

Rice Lake 181881, Technical Manual

Share
Download
Rice Lake 181881 Technical Manual Download Page 62

Load Ranger Wheel Weigh Pad System

56

Visit our website 

www.RiceLake.com

7. Remove jam nut and adhesive protector film from antenna, then slide black O-ring along cable and push into 

adhesive.

8. Position support plate inside of electronics cover with while aligning antenna mounting holes.
9. Insert antenna into electronics cover while threading into support plate.
10. Secure ground to support plate with M3 x 6 screw.
11. Remove CPU board Phillips mounting screw and O-ring from free hole closest to support plate.
12. Secure ground to CPU board mounting hole with previously removed Phillips screw and O-ring.
13. Secure ground to hole in antenna support plate with Phillips screw.

Figure 7-7. Antenna and Ground Wire Installation

14. Align mounting hole in RF module with previously used mounting standoff.
15. Route antenna wire behind RF module then secure RF module with a Phillips screw.
16. Connect antenna wire to RF module.
17. Connect communication cable to RF module and CPU board COM2 TTL.
18. Reconnect power cables to CPU Board.

Figure 7-8. RF module Installation

Antenna

Support Plate

Ground Wire

Mounting Screw 

and O-Ring

Ground Wire and 

Support Plate 

Mounting Screw

COM2 TTL

Antenna Wire

Mounting Screw

RF Module

Summary of Contents for 181881











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands