REX RVF 327 Manual Download Page 98

Page: 98 / 144

RVF 327, 327 S, 330, 330 S
ex no. 1200

Operation of the vacuum filling
machine

page 98 of 144

Version 1.5

Pos.

Installation

sequence

naming

remarks

See remarks Conveyor housing

Permanently installed on the ma-
chine housing

See remarks groove ring

used to seal against meat for the
main drive, leave it on the sliding
drum for cleaning

Sliding drum

Develop for cleaning

vane outside

Develop for cleaning

vane inside

Develop for cleaning

vane inside

Develop for cleaning

vane outside

Develop for cleaning

4.25

INSERTING CONVEYOR PARTS

Rub into, or spray the conveyor parts with food-based, edible fats, or

oils

Insert sliding drum with the help of both leverage keys. The sliding

drum must engage with it in the shank of the input shaft

Put in the vanes

close and lock upper part incl. sliding plate

Attention: Due to the cushioned feeder coupling, the upper section can be

opened in any position with the hopper, or be closed. After start-
ing the Vacuum filling machine, the feeding coupling automatical-
ly engages.



installing the conveyor system

The installation of the conveyor system should only be performed by trained per-
sonnel.

Summary of Contents for RVF 327

















































































































































Search results

Summary of Contents for RVF 327

Reviews:

Related manuals for RVF 327

Brands by name

Popular brands

REX RVF 327, Manual

Search results

Summary of Contents for RVF 327

Reviews:

Related manuals for RVF 327

Brands by name

Popular brands