Regency Fireplace Products Greenfire GF950L Series Owners & Installation Manual Download Page 64

Page: 64 / 104

Regency GF950L-2 Gas Fireplace

GAS POWER FLUE INSTALLATION - END OF LINE POWER FLUE

13-1/2"

(343mm)

Determine

the correct

height

13-1/2"

(343mm)

WARNING

ELECTRICAL CONNECTIONS SHOULD ONLY BE

CARRIED OUT BY A QUALIFIED AND LICENSED ELEC-

TRICIAN

1. Frame an opening to the outside of the building at 343mm W x

343mm H to accommodate the Power Flue.

2. Run the flueing and power flue wire harness from the unit to the framed

opening.

5. Install Power Flue unit into framed opening using 4 screws as shown below.

6. Seal the edges of the Power Flue unit to the framing (there are two seams).

Seal behind flange with silicone--
screw against Plywood siding. Wipe
any excess silicone off outer flange
after flange is screwed down.

Silicone edge of inner trim
against siding of structure,
wipe any excess silicone off
trim.

Fan discharge

opening

343mm

3. Determine the building finishing material thickness.

4. Depending on the building material thickness, install the frame onto the Power

Flue mount using 4 screws. Mounting holes start at 51mm from the front of
the Power Flue unit cover and can be adjusted back in 19mm increments.

NOTE:  Exterior  finishes  such  as  thin  vinyl  siding  may  warp  if  closer  than
51mm  from  the  flue.  For  interior  installations  on  vinyl  siding,  a  51mm
frame/buffer  zone  must  be  created  between  the  finishing  and  the  flue.

Determine protrusion

Determine ﬁnishing

Set frame depth

(starting @ 2" of

faceplate protrusion)

material thickness

of faceplate

Adjustable Power Flue Frame

installation

Summary of Contents for Greenfire GF950L Series









































































































Search results

Summary of Contents for Greenfire GF950L Series

Reviews:

Related manuals for Greenfire GF950L Series

Brands by name

Popular brands

Regency Fireplace Products Greenfire GF950L Series, Owners & Installation Manual

Search results

Summary of Contents for Greenfire GF950L Series

Reviews:

Related manuals for Greenfire GF950L Series

Brands by name

Popular brands