Regency Fireplace Products Greenfire GF950L Series, Owners & Installation Manual

Page: 42 / 104

42
Regency GF950L-2 Gas Fireplace
HORIZONTAL TERMINATIONS - INLINE POWER FLUE
RIGID PIPE 102MM X 168MM
920-210 02.20.20
6
GF950 PV
Inline Power Vent Vertical or Horizontal Installation Instructions
Horizontal Terminations - Inline Power Flue
Rigid Pipe 4" x 6
-5/8" (102mm x 168mm)
The minimum components required for a basic horizontal
termination are:
1 Horizontal Termination Cap
1 Power
Flue Kit
1 Rigid Pipe Adaptor
1 Length of pipe to suit wall thickness and total
flue run
(see Table 1)
Adjustable pipe lengths/slips
Wall thickness is measured from the back standoffs to the inside
mounting surface of termination cap. Create a level surface to mount the
vent terminal. The Terminal must not be recessed into siding. Measure
the wall thickness.
Flat Wall Installation
Wall Thickness
( mm )
Flue Length Required
( mm )
102mm - 140mm 152mm
178mm - 216mm 229mm
254mm - 292mm 305mm
229mm - 368mm
279mm - 371mm Adj. Pipe
381mm - 597mm
432mm - 610mm Adj. Pipe
Pipe Length
Vertical Terminal
Storm Collar
Flashing
Ceiling Firestop
Wall Thimble
o 90 Elbow
Pipe Length
Vent Guard - if required
(Part #946-506/P)
Standoff
Wall Thimble
Pipe Length
Slip Section
Adj. Pipe Length/Slip
Power Flue Terminal
Rigid Pipe Adaptor
(TM) AstroCap
Termination Cap
(Part #946-523/P)
Power Vent Kit (Part 946 - 76 5)
1 51 0-994 Rigid Pipe Adaptor Sold separately
Amount required
for install
102mm x 16 8 mm Rigid Pipe Sold separately
1 666-945 Power Vent Kit Sold separately
1 946-206 Vinyl Siding Standoff Sold separately
1 946-523/P Astro Cap Termination Sold separately
1 Wall Thimble Sold separately
1 946-506/P Vent Guard Sold separately
NOTE: Slip section is mandatory.
Table 1
Important:
Maximum total
flue length = 18m with a maximum of six 90
0
elbows. One 90
0
elbow = two 45
0
elbows.
Maximum total negative flue length = 2.1m .
Note: Maximum length of 18m is based on overall length of
combined chimney components.
Do not run positive flue ing after a negative run.
Inline power flue location restrictions:
Minimum 1.2 m from the unit
Minimum 0.3 m prior to an elbow.
Minimum 0.3 m following an elbow.
Minimum 0.3
m prior to a termination cap.
Minimum 1.8 m rise from top of unit if there is a negative run.
946-763
(Part #946-765)
(Part #510-994)
920-210 04.01.20 6
CV72EPV / CB72EPV
Inline Power Vent Vertical or Hortizontal Installation Instructions
Horizontal Terminations - Inline Power Vent
Rigid Pipe 4" x 6
-5/8"
The minimum components required for a basic horizontal
termination are:
1 Horizontal Termination Cap
1 Power Vent Kit
1 Rigid Pipe Adaptor
1 Vent Reducer
1 Length of pipe to suit wall thickness and total vent run
(see Table 1)
Adjustable pipe lengths/slips
Wall thickness is measured from the back standoffs to the inside
mounting surface of termination cap. Create a level surface to mount the
vent terminal. The Terminal must not be recessed into siding. Measure
the wall thickness.
Flat Wall Installation
Wall Thickness
(inches)
Vent Length Required
(inches)
4" - 5-1/2" 6"
7" - 8-1/2" 9"
10" - 11-1/2" 12"
9" - 14-1/2' 11" - 14-5/8" Adj. Pipe
15" - 23-1/2" 17" - 24" Adj. Pipe
Pipe Length
Vertical Terminal
Storm Collar
Flashing
Ceiling Firestop
Wall Thimble
o 90 Elbow
Pipe Length
Vent Reducer
(Part #946-606)
Vent Guard - if required
(Part #946-506/P)
Standoff
Wall Thimble
Pipe Length
Slip Section
Adj. Pipe Length/Slip
Power Vent Terminal
Rigid Pipe Adaptor
(TM) AstroCap
Termination Cap
(Part #946-523/P)
Table 1
Power Flue Kit (Part 946-765)
1 510-994 Rigid Pipe Adaptor Sold separately
Amount required
for install 102mm x 168mm Rigid Pipe Sold separately
1 946-765 Power Flue Kit Sold separately
1 946-206 Vinyl Siding Standoff Sold separately
1 946-523/P Astro Cap Termination Sold separately
1 946-763 Wall Thimble Sold separately
1 946-506/P Vent Guard Sold separately
1 911-339 PV Wiring Harness Included w/Power Flue Kit
NOTE: Slip section is mandatory.
Important:
Maximum total vent length = 72' with a maximum of six 90
0
elbows.
One 90 0 elbow = two 45 0 elbows.
Maximum total negative vent length = 7'.
Note: Maximum length of 72' is based on overall length of combined
chimney components.
Do not run positive venting after a negative run.
Inline power vent location restrictions:
Minimum 4 ft (1.2 m) from the unit
Minimum 1 ft (0.3 m) prior to an elbow.
Minimum 1 ft (0.3 m) following an elbow.
Minimum 1 ft (0.3 m) prior to a termination cap.
Minimum 6 ft (1.8 m) rise from top of unit if there is a negative run.
IMPORTANT:The inline power flue must be installed within the confines of the home/structure and must be accessible for future servicing. An access hole
as noted in this manual or an attic space would be suitable.
installation