Regency Fireplace Products Greenfire GF950L Series Owners & Installation Manual Download Page 84

Page: 84 / 104

Regency GF950L-2 Gas Fireplace

Replacing the capacitor:

1. Turn off power supply.

2. Loosen the following screws on the terminal block

and pull capacitor out.

3. Ensure the replacement capacitor leads are

inserted correctly into the terminal block with
the red and white wires coming from the power
flue harness.

END OF LINE POWER FLUE MAINTENANCE
INTERNAL POWER FLUE ACCESS

Note: May only be accessed if an access panel was installed for servicing from inside.

1. Turn off the power.

2. Remove 8 Phillips head screws from the rear of the power flue (see Diagram 1).

3. Slide the power flue housing out through the back as shown in Diagram 2.

4. Turn the power flue over to the front side (Diagram 3).

5. Follow Steps 1-9 on previous page.

Front of power flue

Diagram 1

Diagram 2

Diagram 3

maintenance

Summary of Contents for Greenfire GF950L Series









































































































Search results

Summary of Contents for Greenfire GF950L Series

Reviews:

Related manuals for Greenfire GF950L Series

Brands by name

Popular brands

Regency Fireplace Products Greenfire GF950L Series, Owners & Installation Manual

Search results

Summary of Contents for Greenfire GF950L Series

Reviews:

Related manuals for Greenfire GF950L Series

Brands by name

Popular brands