Regency Fireplace Products Greenfire GF950L Series Owners & Installation Manual Download Page 69

Page: 69 / 104

Regency GF950L-2 Gas Fireplace

White/Neutral

installation

GF950

12.14.17

919-637a

OPTIONAL FAN KIT INSTALLATION

FAN DUCT EXTENSION KIT

In order to use the fan extension duct kit, you must have

fan kit. This kit allows you to extend the fan duct to 9m.

1. Attach the connecting collar to the duct that came with the duct kit.

Use the screws provided.

2. Attach the 4.5m duct within this kit to the connecting collar on the opposite

end with the screws provided. Extend the fl ex to the desired length.

WIRING DIAGRAM

Caution: Ensure that the wires do not touch any hot surfaces

and are away from sharp edges.

Alternate Switches: May use the following. Check with local authorities and electrician.

CLIPSAL 203 2E45 OUD - Dimmer

CLIPSAL 2031 VF3CSF - 3 Speed

CAUTION: Label all wires prior to dis-

connection when servicing controls.

Wiring errors can cause improper and

dangerous operation

Wire Nut

Rheostat

Wire Nuts

Wire

Brown (Hot)

Blue (Neutral)

Copper (Earth)

Earth

NOTE: The wires (in dotted lines)

and the wire nuts are not supplied.

Brown

Black

Blue

White

Green

Earth

Heat Wave

Fan Assembly

Fan

120 Volts

60 Hz

240 Volts

50 HZ

Red: Low Speed

Black: High Speed

On/Off Switch

FAN DUCT EXTENSION KIT INSTALLATION

White/Neutral

Black: Active - High speed

Summary of Contents for Greenfire GF950L Series









































































































Search results

Summary of Contents for Greenfire GF950L Series

Reviews:

Related manuals for Greenfire GF950L Series

Brands by name

Popular brands

Regency Fireplace Products Greenfire GF950L Series, Owners & Installation Manual

Search results

Summary of Contents for Greenfire GF950L Series

Reviews:

Related manuals for Greenfire GF950L Series

Brands by name

Popular brands