manualshive.com logo in svg

Raytec VARIO2 series, Full Installation And Setup Manual

Share
Download
Raytec VARIO2 series Full Installation And Setup Manual Download Page 46

46

raytecled.com

Raytec Global Tel: +44 (0) 1670 520055

Americas Tel: +1 613 270 9990

System Information

This page shows basic information about the illuminator including software 
version, product type, illuminator name and group name. This is for information 
only and cannot be altered on this page.

Restore Factory Settings

At any stage, it is possible to restore ALL the original factory settings of the 
illuminator. Any settings that have been previously changed will be lost. During the 
“Restore Factory Settings” the illuminator may come on / flash for a short period.

For Software versions 2.5.x or above: IP address obtained automatically via DHCP
For Software versions < 2.5.0 : Static IP address 192.168.2.80,
See Pages 13 onwards on how to set the IP address of your illuminator.

WARNING:

 Please be aware that this will restore the default IP address of 

the illuminator, which will likely be out of the normal range of IP addresses 
on your network.

Summary of Contents for VARIO2 series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands