RAM 1500 2WD 2021 Owner'S Manual Download Page 175

Page: 175 / 496

STARTING AND OPERATING

173

AXLE LOCK SYSTEM — IF EQUIPPED

This vehicle is equipped with an electronically

locking rear differential. When engaged, this

differential locks the axle shafts forcing the

wheels to spin at an equal rate. The locking of

the rear differential should only be engaged

during low-speed, extreme off-road situations

where one wheel is likely to not be in contact

with the ground. It is not recommended to drive

the vehicle with the differentials locked on

pavement due to the reduced ability to turn and

speed limitations.

Axle Lock Button

The locking rear axle is controlled by the AXLE

LOCK button.
Under normal driving conditions, the rear axle

should be unlocked.
During the command to lock the rear axle, the

indicator light will flash until the axle is locked.

After the lock command has been successfully

executed, the light will remain on solid.
Operating in 4WD LOW the locker can be

engaged up to 40 mph (64 km/h) and will

remain engaged throughout the 4WD LOW

speed range.

Operating the locker in 2WD, 4WD AUTO, and

4WD LOCK/HIGH, the locker can be engaged up

to 20 mph (32 km/h). While driving with the

locker engaged, if speed exceeds 25 mph

(40 km/h), the locker will automatically

disengage, but will automatically reengage at

20 mph (32 km/h).

NOTE:

Left to right wheel speed difference may be

necessary to allow the rear axle to fully lock. If

the indicator light is flashing after selecting the

rear axle lock mode, drive the vehicle in a turn

or on loose gravel to expedite the locking action.

The axle locker could become torque locked

due to side to side loads on the rear axle.

Driving slowly while turning the steering wheel

from a left hand turn to a right hand turn or

driving in REVERSE for a short distance may be

required to release the torque lock and unlock

the axles.

To unlock the rear axle; push the AXLE LOCK

button. The AXLE LOCK indicator light will go out

when the rear axle is unlocked.

CAUTION!



Do not lock the rear axle on hard surfaced

roads. The ability to steer the vehicle is

reduced and damage to the drivetrain may

occur when the axle is locked on hard

surfaced roads.



Do not try to lock the rear axle if the vehicle

is stuck and the tires are spinning. You can

damage drivetrain components. Lock the

rear axle before attempting situations or

navigating terrain, which could possibly

cause the vehicle to become stuck.

21_DT_OM_EN_USC_t.book Page 173

Summary of Contents for 1500 2WD 2021

















































































































































































































































































































































































































































































































Search results

Summary of Contents for 1500 2WD 2021

Reviews:

Related manuals for 1500 2WD 2021

Brands by name

Popular brands

RAM 1500 2WD 2021, Owner'S Manual

Search results

Summary of Contents for 1500 2WD 2021

Reviews:

Related manuals for 1500 2WD 2021

Brands by name

Popular brands