Raleigh Audio Premium Extreme RAKK dac Assembly Manual Download Page 9

Page: 9 / 65

Pre

assemble

(three

input)

I2S

Adapter

with

the

RAKK

dac

————————————————————————————

Skip this section if you do not have a (three-input) I2S Adapter.

————————————————————————————

If you have not yet done so, install the pulse transformers on the RAKK dac.

Mount four 3/8” standoffs on the bottom of the I2S Adapter and secure with 6-32 screws.

Insert a 3/8” 6-32 setscrew about half-way into each 3/8” standoff.

♪

Mount the I2S adapter on the RAKK dac such that the connector on the bottom of the I2S
adapter mates with the connector on the top of the RAKK dac.

Install a 3/8” standoff as a nut on each of the four 3/8” standoffs to hold the two pieces
together.

————————————————————————————

Summary of Contents for Premium Extreme RAKK dac


































































Search results

Summary of Contents for Premium Extreme RAKK dac

Reviews:

Related manuals for Premium Extreme RAKK dac

Brands by name

Popular brands

Raleigh Audio Premium Extreme RAKK dac, Assembly Manual

Search results

Summary of Contents for Premium Extreme RAKK dac

Reviews:

Related manuals for Premium Extreme RAKK dac

Brands by name

Popular brands