Raleigh Audio Premium Extreme RAKK dac Assembly Manual Download Page 43 | Manualshive

Page: 43 / 65

background image

Wire the RAKK dac Inputs

11.

If you have chosen to have an SPDIF or AES/EBU Input 1, connect the violet/black twisted
pair from that jack to the Input 1 pads on the RAKK dac. Connect the violet wire to the “+”
pad and the black wire to the “-” pad.

12.

If you have chosen to have an SPDIF or AES/EBU Input 2, connect the violet/black twisted
pair from that jack to the Input 2 pads on the RAKK dac. Connect the violet wire to the “+”
pad and the black wire to the “-” pad.

13.

If you have chosen to have an SPDIF or AES/EBU Input 3, connect the violet/black twisted
pair from that jack to the Input 3 pads on the RAKK dac. Connect the violet wire to the “+”
pad and the black wire to the “-” pad.

14.

If you have chosen to have a TOSLINK, connect the 19” red/black twisted pair from the 10V
Regulator to the 12V pads on the TOSLINK board. Connect the red wire to the + pad and the
black wire to the – pad.

————————————————————————————

Connect the I2S Inputs to the 3-Input I2S Adapter

Skip this step if you do not have a 3-Input I2S Adapter

15.

Dress the flat cables close to the chassis and connect them to the appropriate inputs on the
I2S Adapter.

————————————————————————————

Wire the USB Adapter and connect it to the 3-Input I2S Adapter

Skip this section if you do not have a USB Adapter.
Skip this step if you do not have a 3-Input I2S Adapter.

16.

Locate the red/black twisted pair from the 8V Regulator and connect it to the 8V pads on the
USB Adapter. Connect the red wire to the “+” pad and the black wire to the “-” pad.

17.

Dress the flat cable close to the chassis and connect it to the appropriate input on the I2S
Adapter.

————————————————————————————

42

«
...
41
42
43
44
45
...
»

Summary of Contents for Premium Extreme RAKK dac


































































Reviews:

No comments

Related manuals for Premium Extreme RAKK dac

Brand: ultimatte Pages: 125

Brand: 3One data Pages: 9

Brand: iConnectivity Pages: 21

Brand: IDK Pages: 44

Brand: APS Pages: 70

Brand: V-TAC Pages: 54

Brand: Patton electronics Pages: 7

Brand: Sencore Pages: 126

Brand: GALCO Pages: 8

GlobeTrotter Ex GE 0003

Brand: Option Audio Pages: 4

COMBIVERT F4-S Series

Brand: KEB Pages: 30

Brand: MyGica Pages: 28

Brand: Parker Pages: 172

1080PXX-LED Button

Brand: EYEZONE Pages: 8

Brand: Pocketdish Pages: 2

Brand: Danfoss Pages: 57

Brand: Kramer Pages: 15

CFG-8700 Series

Brand: Cognex Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands