Raleigh Audio Premium Extreme RAKK dac Assembly Manual Download Page 30 | Manualshive

Page: 30 / 65

background image

♪

Mount the Active Output board

21.

Mount the Active Output board in its location in the center of the chassis.
Orient the board such that the power input pads are closest to the power transformer.
Do not secure the board yet.

22.

Locate the grey twisted pair that is connected to transformer pins B1 and B6. Connect this
twisted pair to the “6.3VAC” pads.

23.

Locate the red twisted pair that is connected to transformer pins 15 and 17 and has a black
wire wrapped around it.

•

These three wires will be connected to the “250V-0-250V” pads.

•

Connect the two red wires to the outer pads.

•

Connect the black wire to the center pad.

24.

Secure the board with thirteen 6-32 x ¼” screws.

25.

Dress the wires:

•

Dress the twisted pairs for the volume control towards the front of the panel.

•

Dress the twisted pairs for the RAKK dac towards the edge of the panel.

•

Dress the green wire from the “chassis” pad towards the rear of the panel.

29

«
...
28
29
30
31
32
...
»

Summary of Contents for Premium Extreme RAKK dac


































































Reviews:

No comments

Related manuals for Premium Extreme RAKK dac

Brand: Yamaha Pages: 32

Brand: ZIEHL-ABEGG Pages: 26

SOLIVIA 2.5 AP G3 TR

Brand: Delta Pages: 48

Brand: OXO Pages: 20

Brand: Transition Networks Pages: 13

Brand: V2 Pages: 4

VFD700-PV-40T00075

Brand: Veikong Pages: 70

Brand: ELECTROCOMPANIET Pages: 16

EZWALL-pro 3x3 v3

Brand: SmartAVI Pages: 14

Brand: Celabs Pages: 2

Brand: Giandel Pages: 8

L.O.C.PRO LP7-4

Brand: PAC Pages: 2

Brand: Shenzhen Huangjintai Electronic Pages: 9

XBMC Clearstream

Brand: Triotech Pages: 16

STORAGE PACKAGE - BUSINESS

Brand: SMA Solar Technology AG Pages: 30

Brand: OLYS Pages: 3

Brand: Danfoss Pages: 148

Brand: B&B Electronics Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands