Raleigh Audio Premium Extreme RAKK dac Assembly Manual Download Page 44 | Manualshive

Page: 44 / 65

background image

Wire the USB Adapter and connect it to the RAKK dac

Skip this section if you do not have a USB Adapter.
Skip this step if you do have a 3-Input I2S Adapter.

18.

Locate the red/black twisted pair from the 8V Regulator and connect it to the 8V pads on the
USB Adapter. Connect the red wire to the “+” pad and the black wire to the “-” pad.

19.

Dress the flat cable close to the chassis and connect it to the “Input 4 I2S” connector on the
RAKK dac

————————————————————————————

Wire the Single-Input I2S Adapter and connect it to the RAKK dac

Skip this step if you do not have a Single-Input I2S Adapter.

20.

Locate the red/black twisted pair from the 5V Regulator and connect it to the 5V pads on the
I2S Adapter. Connect the red wire to the “+” pad and the black wire to the “-” pad.

21.

Dress the flat cable close to the chassis and connect it to the “Input 4 I2S” connector on the
RAKK dac

————————————————————————————

Secure the RAKK dac

22.

Secure the RAKK dac with four 6-32 screws.

————————————————————————————

43

«
...
42
43
44
45
46
...
»

Summary of Contents for Premium Extreme RAKK dac


































































Reviews:

No comments

Related manuals for Premium Extreme RAKK dac

Brand: ICP DAS USA Pages: 85

Brand: ICP DAS USA Pages: 6

Brand: ICP DAS USA Pages: 107

Brand: ICP DAS USA Pages: 8

Brand: ICP DAS USA Pages: 12

OTEC IEWQ Series

Brand: Omega Pages: 29

Brand: ICP DAS USA Pages: 7

Brand: Planet Pages: 32

Brand: Wentronic Pages: 4

Brand: Bladelius Pages: 6

Brand: BASETech Pages: 8

Brand: Transition Networks Pages: 7

Brand: T4T Pages: 42

Brand: Actox Pages: 36

Brand: BluStream Pages: 21

Brand: Srne Pages: 35

LinkTheater LT-H90LAN

Brand: Buffalo Pages: 59

Brand: Vertex Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands