Raleigh Audio Premium Extreme RAKK dac Assembly Manual Download Page 49 | Manualshive

Page: 49 / 65

background image

Wire the Power-on LED

3.

Locate the violet/white twisted pair from the 12V power supply board.

4.

Solder the wires to the LED leads.

•

Connect the violet wire to the anode. The anode is the longer of the two leads.

•

Connect the white wire to the cathode.

————————————————————————————

Wire the Power Switch

The power switch has four terminals (two pairs.) One pair will be used to control the power
on/off and the other pair will be used to provide a fast mute for power off.

5.

Connect the #20 black twisted pair from the white/black power cable to the two terminals on
the power-on switch that are closest to the bottom of the panel.

6.

Connect the #22 black twisted pair from the “external mute” on the Active Output to the two
terminals on the power-on switch that are closest to the top of the panel.

————————————————————————————

48

«
...
47
48
49
50
51
...
»

Summary of Contents for Premium Extreme RAKK dac


































































Reviews:

No comments

Related manuals for Premium Extreme RAKK dac

Brand: Paradox Pages: 2

Brand: Samsung Pages: 37

Brand: Samsung Pages: 2

Brand: ICP DAS USA Pages: 113

Brand: IDK Pages: 44

blueplanet 1502xi

Brand: Kaco Pages: 56

Brand: IMO Pages: 94

Brand: iLive Pages: 12

Brand: Xantech Pages: 2

Mega 100 Classic

Brand: Ellumiglow Pages: 4

Brand: Goobay Pages: 8

OPS500-501 Series

Brand: AXIOMTEK Pages: 54

Brand: Cablematic Pages: 3

Brand: e+p Pages: 2

Brand: Xantrex Pages: 124

Brand: ABK Pages: 17

Brand: Phrontier Technologies Pages: 16

Brand: Xantrex Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands