Raleigh Audio Premium Extreme RAKK dac Assembly Manual Download Page 11

Page: 11 / 65

Pre

wire

the

10V

Regulator

(for

the

RAKK

dac)

————————————————————————————

Prepare a 20” #22 red/black twisted pair.

•

Connect the red wire to the DC Output “+” pad.

•

Connect the black wire to the DC Output “-” pad.

————————————————————————————

Skip the following step if you do not have a three-input I2S Adapter.

4.

Prepare a single 22” #22 red wire.

•

Connect the wire to the DC Output “+” pad.

•

Wrap the wire around the red/black twisted pair.

————————————————————————————

Skip the following step if you do not have a TOSLIKK adapter.

5.

If you have a TOSLINK input, prepare a 19” #22 red/black twisted pair.

•

Connect the red wire to the DC Output “+” pad.

•

Connect the black wire to the DC Output “-” pad.

————————————————————————————

Pre

wire

the

Regulator

(for

the

three

input

I2S

Adapter)

Skip this section if you do not have a three-input I2S Adapter.

————————————————————————————

Prepare a 22” #22 red/black twisted pair.

•

Connect the red wire to the DC Output “+” pad.

•

Connect the black wire to the DC Output “-” pad.

————————————————————————————

Summary of Contents for Premium Extreme RAKK dac


































































Search results

Summary of Contents for Premium Extreme RAKK dac

Reviews:

Related manuals for Premium Extreme RAKK dac

Brands by name

Popular brands

Raleigh Audio Premium Extreme RAKK dac, Assembly Manual

Search results

Summary of Contents for Premium Extreme RAKK dac

Reviews:

Related manuals for Premium Extreme RAKK dac

Brands by name

Popular brands