RadioLink AT9S PRO Manual Download Page 4

Page: 4 / 83

Radiolink Electronic Ltd

www.radiolink.com

III Acro Advance Menu ·························································································· ·············· · 31

3.1 Airplane Wing Types(Acro/Glid) ··································································· ·············· · 31

3.2 Twin Aileron Servos (5-channel receiver, AILE-2 , ACRO/GLID) ···························· ·············· 31

3.3 Acro Advance Function Menu ······································································ ·············· · 32

3.3.1 Program Mix ····················································································· ·············· · 33

3.3.2 Curve Programmable Mixes (PROG.MIX5-8)(HELI: PROG.MIX5-6 ) ·············· ·············· 36

3.3.3 Flaperon (ACRO/GLID 1A+1F ) ···························································· ·············· · 37

3.3.4 Flap-Trim ··························································································· ·············· 38

3.3.5 Aile Diff (ACRO/ GLID 2A+1F/ GLID 2A+2F) ············································ ·············· · 39

3.3.6 Air Break (ACRO/ GLID) ······································································ ·············· · 40

3.3.7 Elev-Flap mixing (ACRO/GLID) ······························································ ·············· 41

3.3.8 Dual Elevator Servos (with a rudder) (AILEVATOR) (ACRO) ························· ·············· 42

3.3.9 Snap Rolls (ACRO) ············································································ ·············· · 43

3.3.10 V-Tail (ACRO/ GLID) ·········································································· ·············· · 44

3.3.11 Elevon ··························································································· ·············· · 45

3.3.12 Gyro Sense ······················································································ ·············· · 45

3.3.13 Thr-Delay (ACRO) ············································································· ·············· · 46

3.3.14 Thr Curve (ACRO) ············································································· ·············· · 47

3.3.15 Throttle-Needle mixing (ACRO/ HELI) ··················································· ·············· · 48

IV Glider Model Functions ····················································································· ·············· · 49

4.1 Set Basic Menu of Glid ················································································ ·············· · 49

4.2 Set Glid Type ···························································································· ·············· · 51

4.3 Glid Advance Menu ···················································································· ·············· · 52

4.3.1 Aile Diff ( In ACRO FUNCTION MENU 3.3.5) ············································· ·············· · 52

4.3.2 Flaperon ( In GLID 1A+1F, In ACRO 3.3.3) ·············································· ·············· · 52

4.3.3 V-Tail ( In ACRO 3.3.10) ········································································ ·············· · 52

4.3.4 Offset (GLID 2A+2F) ············································································ ·············· · 52

4.3.5 Start Delay (GLID 1A+1F only) ······························································· ·············· · 53

4.3.6 Chamber-Flp ···················································································· ·············· · 54

4.3.7 Camber Mixing ··················································································· ·············· · 55

4.3.8 Butterfly (crow) Mixing ········································································ ·············· · 55

4.3.9 Aile/ Rudd Mix ···················································································· ·············· · 57

4.3.10 Elev-Flap Mixing (In GLID 3.3.7) ··························································· ·············· · 57

4.3.11 Aile-Flap (GLID 2A+2F only) ······························································· ·············· · 57

4.3.12 Spoiler Mix (GLID) ············································································· ·············· · 58

4.3.13 Flap-Trim (In GLID 3.3.4)····································································· ·············· · 59

4.3.14 Condition ························································································· ·············· · 59

V Helicopter Model Functions ················································································ ·············· · 59

5.1 Basic Setting ··························································································· ·············· · 59

5.2 Heli-Specific Basic Menu Functions ································································ ·············· · 61

Summary of Contents for AT9S PRO




















































































Search results

Summary of Contents for AT9S PRO

Reviews:

Related manuals for AT9S PRO

Brands by name

Popular brands

RadioLink AT9S PRO, Manual

Search results

Summary of Contents for AT9S PRO

Reviews:

Related manuals for AT9S PRO

Brands by name

Popular brands