RadioLink AT9S PRO Manual Download Page 60 | Manualshive

Page: 60 / 83

background image

Radiolink Electronic Ltd

www.radiolink.com

55

Adjustability:

• Delay time (

-DLY-) range of 0 to 100%. The delay time is 10 second at 100%.

Goals

Steps

Inputs

Ex: delay time=5
second.

Open ADVANCE menu,
then open START DELAY.

to BASIC .

again to ADVANCE

to START-DLY,

Activate the function

to MIX

，

to OFF or ON

Set the delay time.
(Ex:50% each surface)

to ELEV

，

to 50%

to RUDD

，

to 50%

Repeat as needed.

Close

4.3.6 CHAMBER-FLP

CAMBER FLAP assigns the primary flap control [defaults to VR (A)] to allow trimming in flight of the flap
action. The up and down travel of each flap (camber flaps: FLP1/2) can be adjusted independently. Also the
center position of flap servo can be offset.

Note: If FLAP-TRIM is activated, you can not use CAMBER

FLAP function simultaneously.

Adjustability

• Rate:

-100% to +100%, with a default of +30%

• Center position (CENTER): The operation reference point of flap

can be offset. -100% to +100%, with a default of 0%.

Note: When changing the polarity of a rate, "change rate dir?"

is displayed for a check. Please set up after pressing DIAL for 1
second and canceling an alarm display.

Goals

Steps

Inputs

Ex: Set the maximum
travel of 35% of the
total flap travel.

Open the CAMBER FLAP
function.

to BASIC .

again to ADVANCE

to CAMBER-FLP,

Adjust the up/down trim
amount separately.(Ex:
adjust to 35%)

to FLP

。

VR (A)

，

to 35%

，

VR (A)

，

to 35%

，

。

Repeat.

Or: adjust the center position
of flap servo

to CENTER

，

to desired point.

Close

«
...
58
59
60
61
62
...
»

Summary of Contents for AT9S PRO




















































































Reviews:

No comments

Related manuals for AT9S PRO

Brand: YASKAWA Pages: 256

Brand: Watts Pages: 2

Brand: Hanbay Pages: 18

ESD-5550 Series

Brand: GAC Pages: 12

Brand: Parkside Pages: 65

Brand: Data Signs Pages: 23

Brand: National Instruments Pages: 19

iEP-5000G Series

Brand: ASROCK Pages: 2

Brand: Code Alarm Pages: 21

Brand: Runxin Pages: 4

Brand: Texas Instruments Pages: 25

Brand: KAR-TECH Pages: 55

10 AMP RVC-MPPT

Brand: Go Power Pages: 17

Brand: Gain Electronic Pages: 17

Brand: Vexve Pages: 24

Brand: HBM Pages: 88

Brand: Nustart Pages: 12

Brand: SUPMEA Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands