RadioLink AT9S PRO Manual Download Page 45 | Manualshive

Page: 45 / 83

background image

Radiolink Electronic Ltd

www.radiolink.com

40

traveled as FLAPERON/SPOILERON by changing the Flap Trim travel.

Goals

Steps

Inputs

Add FLAP-TRIM to allow

the model’s ailerons to

be trimmed together as
flaps at any time during
the flight, with a
maximum travel of 5% of
the total flap travel set in
FLAPERON.

Open FLAP-TRIM function

to BASIC

again to ADVANCE

to FLAP-TRIM.PUSH.

The function is automatically activate with FLAPERON; however the default
travel is 0.

Adjust the travel available to
the FLAPERON when
turning the CH6 dial.

to 5%

Close

3.3.5 AILE DIFF (ACRO/ GLID 2A+1F/ GLID 2A+2F)

ACRO GLID (2A+1F)/GLID (2A+2F)

Aileron differential is primarily used on 3 or 4-servo wings, with one servo operating inboard flap on CH6 or
CH5 & CH6, and AILE-DIFF controlling proper aileron operation of 2 aileron servos, plugged into CH1 and
CH7. The ailerons can not be moved like flaps when using AILE-DIFF, except if using AIRBRAKE. (Note that
even if you make FLAP-TRIM active while using AILE-DIFF, it will not have any effect. ONLY AIRBRAKE
controls the ailerons as flaps in the AILE-DIFF configuration.)

Note: When changing the polarity of a rate in camber-flap, "change rate dir?" is displayed for a check.

Please set up after pressing DIAL for 1 second and canceling an alarm display. (GLID only)

•

FLAP function allows you to set up 1 or 2 servos for flap action.

• The separate AILE

-DIFF settings for each condition can be set. (GLID only)

Goals

Steps

Inputs

Activate twin aileron servos
using AILE-DIFF.
Note that the function
defaults to no difference in
down travel vs. up travel. If
you want differential travel,
simply adjust each side.
(Ex: 90%)

Open the FLAPERON.

to BASIC menu,

again to ADVANCE

to AILE-DIFF .PUSH.

Activate the function.

to MIX

，

PUSH.

to ACT

Optional: adjust the
up/down travel for 2
servos..(Ex:90% down)

to AILE1

AILERON STICK.

to 90%

to AILE2,

AILERON STICK

，

to 90%

Close

* If you receive an error message that OTHER WING MIXING IS ON, you must deactivate ELEVON or
FLAPERON.

«
...
43
44
45
46
47
...
»

Summary of Contents for AT9S PRO




















































































Reviews:

No comments

Related manuals for AT9S PRO

TLE Scalable 150

Brand: GE Pages: 6

Brand: GE Pages: 3

Brand: GE Pages: 80

PACSystems* RX3i

Brand: GE Pages: 39

PACSystems* RX3i

Brand: GE Pages: 35

PACSystems* RX3i

Brand: GE Pages: 3

PACSystems* RX3i

Brand: GE Pages: 169

PACSystems RX7i

Brand: GE Pages: 317

Brand: IDK Pages: 96

Brand: Paradox Pages: 2

Brand: Paradox Pages: 44

Brand: Ziton Pages: 28

Brand: Unico Pages: 164

Brand: DANIEL Pages: 48

Brand: Maximum Controls Pages: 58

Brand: FUTABA Pages: 8

Brand: DSEGenset Pages: 74

Brand: ITALFARAD Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands