RadioLink AT9S PRO Manual Download Page 75

Page: 75 / 83

Radiolink Electronic Ltd

www.radiolink.com

Goals

Steps

Inputs

Fine-tune hovering with the hovering
adjustments. Remember these
affect only the hovering (normal)
condition.

Adjust throttle and collective pitch
curves until model hovers nicely. In

flight,adjust collective pitch and
throttle
curves near hover point independently
with HOV-THR and HOV-PIT knobs.

Store new settings after flight.

Open the HOV-THR function

to BASIC.

again to

ADVANCE, to HOV-THR.

Optional: change which
knob adjust seach hovering
curve.

NULL

locks in curve

in last stored position.

to VR

，

to desired knob

and direction

Open the HOV-PIT function.

to HOV-PIT.

Repeat.

5.3.6 HIGH/LOW PITCH (HI/LO-PIT):

This function may be used to adjust the curves high and low side
individually for each flight condition (normal, idle-up 1, idle-up 2, idle-up 3,
throttle hold).

Adjustability:

• You may define high and low side rate trim knobs (the high side pitch trim

control is defined as the right side lever at initial setting).

• The conditions are activated i

n the CONDITION SELECT function.

• Both adjustments may be set to MANUAL, temporarily turning off the knob.

• Adjustments may be memorized and then return the knobs to center point to use that amount of adjustment,

allows easy use of the trimming knobs for multiple models.

Goals

Steps

Inputs

Set up a high pitch
curve in the idle-up
1condition.

Open the HI/LO-PIT

to BASIC menu,

again to ADVANCE menu.

to HI/LO-PIT.

Select the idle-up 1 condition

to COND

，

to IDL1

Set the rate (Ex:80%)

to HI-PIT

，

to 80%

Optional

：

Change which knob

adjusts high pitch curve.

to VR

，

to desired knob and direction.

Summary of Contents for AT9S PRO




















































































Search results

Summary of Contents for AT9S PRO

Reviews:

Related manuals for AT9S PRO

Brands by name

Popular brands

RadioLink AT9S PRO, Manual

Search results

Summary of Contents for AT9S PRO

Reviews:

Related manuals for AT9S PRO

Brands by name

Popular brands