RadioLink AT9S PRO Manual Download Page 61 | Manualshive

Page: 61 / 83

background image

Radiolink Electronic Ltd

www.radiolink.com

56

4.3.7 Camber Mixing:

This function adjusts the mixing rate of camber operation which
operates the wing camber (ailerons and flaps) in the negative and
positive directions. The aileron, flap, and elevator rates can also be
adjusted independently and attitude changes caused by camber
operation can be corrected.
Also the operation reference point of camber control can be offset.
(PRE)

Note: Camber control is not assigned at initial.

Adjustability:

• Rate:

-100% to +100%, with a default of +30%

• Reference point (PRE): The operation reference point of camber control can be offset.

-100% to +100%,

with a default of 0%.

4.3.8 BUTTERFLY (crow) mixing

BUTTERFLY simultaneously moves the flaps, twin ailerons and elevator, and is usually used to make steep
descents or to limit increases in airspeed in dives. Separate two BUTTERFLY settings are available.
(CRI1/CRI2)
Adjustability:

• Activation: Get proportional by moving the THROTTLE STICK.

Goals

Steps

Inputs

Ex: set the mixing
amount for aileron
to 40%, camber
control to VR (E),
reference point to
desired point.

Open the CAMBER MIX
function.

to BASIC .

again to ADVANCE

to CAMBER-MIX,

Choose desired slider.

to VR

，

to VrA

Adjust the mixing amount for
AILE. (Ex: adjust to 40%)

to FLP

to VrA

，

to 40%,

to VrA

，

to 40%

，

Set the reference point.

to PRE

，

or

VrA to desired

point

for 1 sec.

Close

«
...
59
60
61
62
63
...
»

Summary of Contents for AT9S PRO




















































































Reviews:

No comments

Related manuals for AT9S PRO

Brand: Ubisys Pages: 2

Brand: IDK Pages: 96

Brand: K&K Pages: 6

Brand: Yamaha Pages: 92

U1000 iQpump Drive

Brand: YASKAWA Pages: 26

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 2

Brand: YASKAWA SIEMENS Pages: 373

Brand: Gardena Pages: 236

Brand: Vertiv Pages: 2

Brand: Quantum Pages: 20

M-DUINO PLUS series

Brand: Industrial Shields Pages: 46

Brand: Qianjin Electronic Pages: 39

MSI-EM-IO84NP Series

Brand: Leuze electronic Pages: 22

GYRO TECH Nabco Multi-Module

Brand: Nabco Pages: 21

Brand: NI Pages: 135

Brand: Samson Pages: 24

Brand: fafnir Pages: 16

Brand: YOKOGAWA Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands