RadioLink AT9S PRO Manual Download Page 53

Page: 53 / 83

Radiolink Electronic Ltd

www.radiolink.com

auxiliary channel such as 8, and then using some creative mixes.

Goals

Steps

Inputs

Activate
THR-DELAY for a
ducted-fan replica
of a
turbine-powered
MULTIROTOR.
Slow the servo
response by one
second.

Open THR-DELAY

to BASIC .

again to ADVANCE

to THR-DELAY,

Activate the function.

to MIX.PUSH.

to ACT.

Adjust the RATE to match the
desired servo speed.(Ex:40%)

to RATE.PUSH

to 40%

3.3.14 THR CURVE (ACRO)

This function adjusts the throttle operation curve for optimum the engine
speed to throttle stick movement.

Note: If the throttle EXP function is activated, you can not use

THR-CURVE function simultaneously.

Adjustability:

• Separate curves for each switch position are available.

• Moving and deleting the curve point: The curve point (

-STK-) can be

moved to the left or right by turning the DIAL (up to 2% in front of the adjoining point) and deleted/returned by
pressing the DIAL for one second alternately.

Goals

Steps

Inputs

Base point: Adjust base point of
throttle curve until engine idles
reliably.
-Out-:output,servo position.
-STK-: curve point, stick position.

Open THR-CURVE

to BASIC .

again to ADVANCE

to THE-CURVE,

Activate the function.

to MIX.PUSH

to ON.

Adjust the 1

point

to P1(

-out-)

.PUSH

to desired servo

position

Optional: assign the switch.

to SW.PUSH

，

to desired switch.

Optional: Move the curve
point.(Ex: point 3)

to P

3 (-stk-)

,PUSH

to desired

curve point to move to left or right.

Optional: delete the curve
point. And return the curve
point.(Ex: point 3)

to P

3 (-stk-)

for 1sec.to delete the

curve point.

to P

3 (-stk-)

，

for 1sec.to return

Adjust the next point.

Repeat as needed.

Summary of Contents for AT9S PRO




















































































Search results

Summary of Contents for AT9S PRO

Reviews:

Related manuals for AT9S PRO

Brands by name

Popular brands

RadioLink AT9S PRO, Manual

Search results

Summary of Contents for AT9S PRO

Reviews:

Related manuals for AT9S PRO

Brands by name

Popular brands