RadioLink AT9S PRO Manual Download Page 42 | Manualshive

Page: 42 / 83

background image

Radiolink Electronic Ltd

www.radiolink.com

37

Other samples:

• RUD

-ELEV (ACRO GLID) mix: Compensate for pitching up or down when rudder is applied.

• AIL

-RUD mix (ACRO): Coordinate turns by applying rudder automatically with aileron input. All model types.

• ELE

V-PIT (HELI) mix: Compensate for the loss of lift of tilting the model

3.3.2 Curve Programmable Mixes (PROG.MIX5-8)(HELI: PROG.MIX5-6 ):

AT9S Pro

’s ACRO/GLID programs contain four separate curve programmable mixes. HELI contains two.

There are a variety of reasons you might want curve mixes. Usually a linear mix doesn't fit your needs along
the whole range. One pre-programmed curve mix is the THROTTLE-NEEDLE function. This curve is

adjustable at 5 points, allowing you to adjust the motor’s tuning at 5 poin

ts along its RPM range.

One programmable curve mix defaults to RUDDER-AILERON. A linear mix that keeps the model from rolling
in knife-edge is probably too much aileron when rudder is applied in level flight. Create a curve mix and set all
5 points to match the linear mix. Inhibit the linear mix, and then adjust the curve to get the right response all

along the rudder channel’s travel.

Adjustability:

• ACRO/GLID Defaults: The 4 programmable curves mixes default to the most frequent choice

s, but can be

set to any channel.

• PROG.MIX5 rudder

-to-aileron for roll coupling compensation (GLID mixes default to aileron-to-ELEV.)

• PROG.MIX6 rudder

-to-aileron for roll coupling compensation (GLID mixes default to aileron-to-ELEV.)

• PROG.MIX7 rudder

-to-elevator for pitch coupling compensation (GLID mixes default to

elevator-to-airbrake.)

• PROG.MIX8 rudder

-to-elevator for pitch coupling compensation (GLID mixes default to

elevator-to-airbrake.)

• HELI Defaults:

• PROG.MIX5 aileron

-to-elevator for coordinated turns

• PROG.MIX6 aileron

-to-elevator for coordinated turns

• Master: The controlling channel can only be a channel. Cannot OFFSET or dial.

• Trim: not available in curve mixes.

• Offset: not available in curve mixes.

Goals

Steps

Inputs

Set up a RUDD-ELEV curve
mix on a model that pitches
down severely at full rudder
and not at all with minimal
rudder input, and pitches
worse on right rudder than
left:

Open an unused
programmable mix.(Ex: use
PROG.MIX7 since it is already
set up for FLAP-ELEVATOR)

to BASIC menu,

again to

ADVANCE

to PROG.MIX PUSH

7

，

PUSH

Activate the function

to MIX

，

PUSH

，

to ON, PUSH

Choose master and slave
channels.

Already RUDD. Already ELEV

«
...
40
41
42
43
44
...
»

Summary of Contents for AT9S PRO




















































































Reviews:

No comments

Related manuals for AT9S PRO

Brand: VAT Pages: 29

Brand: Balboa Instruments Pages: 19

Brand: Canarm Pages: 3

Brand: Watts Pages: 2

Brand: Hanbay Pages: 18

Brand: Barthelme Pages: 8

Brand: CAB Pages: 28

Brand: C-TEC Pages: 16

Brand: C&T Solution Pages: 27

SECURIT ST800L+

Brand: C&K systems Pages: 16

Brand: Samson Pages: 40

Brand: Jabra Pages: 8

Brand: Paradox Pages: 32

Brand: Xantrex Pages: 56

Brand: Xantrex Pages: 2

Freedom Sequence

Brand: Xantrex Pages: 58

Brand: Xantrex Pages: 4

Brand: Xantrex Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands