RadioLink AT10II Instruction Manual Download Page 48

Page: 48 / 88

Radiolink Electronic Ltd

www.radiolink.com

FLAP-TRIM assigns the primary FLAPERON control [defaults to VR(A)] to allow trimming in flight of

the flap action of FLAPERON.

Note: Even if FLAP-TRIM is made active with AIL-DIFF, it will not have any effect. The ONLY

function that allows control of the ailerons as flaps in the AIL-DIFF configuration is AIRBRAKE. Most

modelers use AIRBRAKE, or programmable mixes, to move the flaps to a specified position via

movement of a switch.

FLAP-TRIM may also be used as the primary flap control in flight. By doing so, you can assign CH6

to a 3-position switch, with a "SPOILERON", neutral, and "FLAPERON" position, and even adjust

the percentage traveled as FLAPERON/SPOILERON by changing the Flap Trim travel.

Goals

Steps

Inputs

Add FLAP-TRIM to

allow the model’s ailerons

to be trimmed together as

flaps at any time during

the flight, with a

maximum travel of 5% of

the total flap travel set in

FLAPERON.

Open FLAP-TRIM function

to BASIC

again to ADVANCE

to FLAP-TRIM.PUSH.

The function is automatically activate with FLAPERON; however the default

travel is 0.
Adjust the travel available to

the FLAPERON when turning

the CH6 dial.

to 5%

3.3.5 AILE DIFF (ACRO/ GLID 2A+1F/ GLID 2A+2F)

ACRO

GLID (2A+1F)/GLID (2A+2F)

Aileron differential is primarily used on 3 or 4-servo wings, with one servo operating inboard flap on

CH6 or CH5 & CH6, and AILE-DIFF controlling proper aileron operation of 2 aileron servos, plugged

into CH1 and CH7. The ailerons can not be moved like flaps when using AILE-DIFF, except if using

AIRBRAKE. (Note that even if you make FLAP-TRIM active while using AILE-DIFF, it will not have

any effect. ONLY AIRBRAKE controls the ailerons as flaps in the AILE-DIFF configuration.)

Note: When changing the polarity of a rate in camber-flap, "change rate dir?" is displayed for a

check. Please set up after pressing DIAL for 1 second and canceling an alarm display. (GLID only)

•

FLAP function allows you to set up 1 or 2 servos for flap action.

• The separate AILE-DIFF settings for each condition can be set. (GLID only)

Goals

Steps

Inputs

Activate twin aileron servos

using AILE-DIFF.

Note that the function

defaults to no difference in

down travel vs. up travel. If

you want differential travel,

simply adjust each side. (Ex:

90%)

Open the FLAPERON.

to BASIC menu,

again to ADVANCE

to AILE-DIFF .PUSH.

Activate the function.

to MIX

，

PUSH.

to ACT

Optional: adjust the

up/down travel for 2

servos..(Ex:90% down)

to AILE1

AILERON STICK.

to 90%

to AILE2,

AILERON STICK

，

to 90%

Summary of Contents for AT10II

























































































Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands

RadioLink AT10II, Instruction Manual

Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands