RadioLink AT10II Instruction Manual Download Page 87

Page: 87 / 88

Radiolink Electronic Ltd

www.radiolink.com

6.1 MULTIROTOR BASIC MENU

The basic function menu is same like ACRO, GLID and HELI, please find the detail in the former

chapters. Below is the special option:

6.1.1 MODEL TYPE

Different from ACRO, GLID AND HELI, MODEL TYPE for MULTIROTOR has an additional function

TRIM, which is controlled by the VR switch. Set the TRIM OFF to avoid a mis-operation damage to

the model.

Goals

Steps

Inputs

Select proper MODEL

TYPE. (Ex:

MULTIROTOR

）

Open BASIC menu, find

MODEL TYPE.

Turn on the transmitter,

for 1 sec. to BASIC

menu (If ADVANCE,

again)

to MODEL TYPE

Go to MODEL TYPE

to TYPE

Choose proper model type

(Ex: MULTIROTOR).

Confirm the change.

to MULTIROTOR,

for 1 sec. ‘Are you sure?’

Displays,

to confirm.

Turn on the trim.

to AILE-TR

to ON.

Repeat above to turn on other trims

6.1.2 AUX Channel setting

AUX channel for MULTIROTOR is channel 6 to 10, same like ACRO, GLID and HELI, to set

auxiliary channel. CH5 is special for ATTITUDE, enter CH5 and press PUSH for ATTITUDE. Select

3-section and 2-section switch to get 6 different attitudes. By DIAL set 6 different rates according to

the attitudes.

6.2 ADVANCE MENU FOR MULTIROTOR

6.2.1 ATTITUDE

There are 6 different attitude modes for MULTIROTOR: NORMAL, ATTI, GPS, HOVER, F/S and

AUX. Every mode will have a different rate to get a unique signal. NORMAL mode preset 0%, ATTI

50%, GPS 100%, HOVER 25%, F/S 75% and AUX 50%.

0% means a output signal 1ms, and 100% means 2ms. You can totally get 6 different modes by

adjusting the related rates.

Summary of Contents for AT10II

























































































Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands

RadioLink AT10II, Instruction Manual

Search results

Summary of Contents for AT10II

Reviews:

Related manuals for AT10II

Brands by name

Popular brands